Skip to content
Safe LiftSYSTEMS

Choosing a lift for a Toronto shop

A Toronto bay is often narrower and lower than the brochure assumes. We sell Rotary, BendPak, Atlas, Forward and more, and we match the lift to your work and your building.

What we ask first

We want the job mix before the model number. Our own crew installs what we sell, so we care that it fits.

  • The vehicles you lift most, and the heaviest one
  • Bay width, depth and clear height, measured to the lowest obstruction
  • Slab thickness, if you know it
  • Owned or leased
  • Power at the bay
  • An old lift to trade in, if any

Low ceilings and narrow units

A 2017 City study says converted warehouses in the Port Lands and South of Eastern often have low ceilings with limited clear span. That rules some lifts out before you compare brands.

In a low unit, look at low-rise and scissor lifts, or a four-post with rolling jacks. Where the landlord won't allow anchors, mobile column lifts and freestanding four-posts are worth a look.

Measure before you shop. A spec sheet lists the lift's overall height, but the vehicle on top needs room too, and so does the tech working under it.

Fleet shops and electric vehicles

Toronto's public fleets are going electric. The City's 2026 budget notes list 415 EV chargers across its fleet, and the TTC is working toward a zero-emissions bus fleet by 2040.

If you run a fleet, buy for the vehicles you plan to run next, not only today's. Battery vehicles are heavy and have set lift points, so check capacity and adapters against them.

For vans, trucks and buses, heavy-duty two-posts, drive-on four-posts and mobile columns are the common picks. Ask about wheelbase range and axle weight, not just total capacity.

Dealers, collision and tire shops

A dealer service department often starts with two-posts for general work and a four-post for alignments. Some vehicle makers run equipment programs that name the equipment for certain bays, so ask your manufacturer before ordering for those.

Collision shops like lifts that leave the sides of the car open, such as scissors and low-rise lifts. Tire shops want fast cycles through the spring and fall rush, so low-rise and two-post lifts are common.

For tire work, also ask how quickly the arms or pads set on the cars you see most. Seconds per car add up over a busy week.

Big footprints in East York

In East York, the Laird in Focus study describes large-format, low-rise buildings with surface parking around Laird Drive and Eglinton Avenue East. A bigger floor plate may allow wider bays or a drive-through layout, but height and slab still need checking.

In South of Eastern and the Port Lands, the City notes a long habit of reusing existing buildings. We measure each unit before we recommend a model.

Trading in or buying used

Replacing a worn lift? We look at trade-ins case by case, and we buy some used lifts too.

Running more than one location in the city? Tell us. We can plan lifts for each site at once and keep models consistent, so your techs know every bay.

Found a used lift yourself? We install lifts bought elsewhere. Send the make, model and spec sheet, and we tell you whether it suits your bay. New or used, Ontario Regulation 851 calls for an exam before first use, and we can book it with the install.

Common questions

What lift works in a low Toronto unit?

It depends on your clear height and the work. Low-rise lifts, scissor lifts and four-posts often fit where a tall clearfloor two-post won't. We measure before we recommend one.

Which brands do you sell?

Rotary, BendPak, Atlas, Forward and more. We also service most other brands, so a shop with a mix of lifts is fine.

Do you take trade-ins?

Yes, case by case. Send the make, model and rough age of the old lift, and we look at it when we quote the new one.

Can my landlord stop me from anchoring a lift?

A lease can limit anchoring and wiring, so read yours. If anchors are out, mobile column lifts and freestanding four-posts don't bolt to the floor.

Can a dealership pick any lift it wants?

Not always. Some vehicle makers name specific equipment for some bays. Check with your manufacturer first. For bays outside those programs, the choice is yours.

Pricing a new lift?

Send your ceiling height and what you work on. You get one price for the lift, delivery and install.