Skip to content
Smart LiftingSYSTEMS

Two-post lifts for general repair shops

A two-post picks the vehicle up by the frame so the wheels hang free. It gives your tech the best access underneath of any lift type.

7,000–12,000lb

Get a quote

Who a two-post is for

It is the everyday lift in a general repair shop. Around 10,000 lb is the common choice for cars, SUVs and half-ton pickups.

If you take three-quarter and one-ton pickups, heavier vans or a lot of EVs, most shops step up to 12,000 lb. Box trucks and fleets belong on our heavy-duty truck lift page.

How it works

Four swing arms go under the frame or pinch welds. The arms have limits too, not just the total. A common 10,000 lb two-post may be rated for only 5,000 lb on either axle and 2,500 lb on any one arm.

On an EV, the arms go on the maker's lift points, never under the battery pack.

Clearfloor or floorplate

A clearfloor model runs its cables and hoses through a beam across the top. The floor stays clear, and a shutoff bar stops the lift if a tall vehicle touches it.

A floorplate model runs them through a plate you drive over. Nothing sits above the columns, so it needs much less ceiling. On a low ceiling it is the right machine, not a downgrade.

Symmetric or asymmetric

A symmetric lift centres the vehicle between the columns. The load is balanced, which suits long, heavy trucks and vans, but the doors open into the columns.

An asymmetric lift sets the car further back so the doors clear the posts. Many lifts now have arms that do both, which suits a shop doing cars and trucks.

What your bay needs

A clearfloor 10,000 lb two-post is roughly 12 to 13 ft tall on common models. Measure to the lowest thing over the lift, like lights, heaters, sprinkler heads or door tracks, not the roof deck. With less than about 12 ft clear, look at a floorplate model.

Check the door opening too, not just the ceiling.

What your bay needs

Measure to the lowest thing overhead. Final numbers come from the spec sheet of the exact model.

Bay requirements
Ceiling, clearfloor 10,000 lb12 to 13 ft overall, roughly
Ceiling under about 12 ftFloorplate model
Overall width, 10,000 lb11 to 12 ft, roughly
Drive-through between columns7.5 to 9 ft, roughly
Slab, BendPak 7,000 to 10,000 lb4-1/4 in, 3,000 PSI
Power, BendPak 10APX220 V, single phase

Before install day

  • Slab thickness goes up with capacity. BendPak calls for 4-1/4 in at 7,000 to 10,000 lb, 6-1/2 in at 12,000 lb and 8 in at 15,000 and 18,000 lb. Every maker publishes its own numbers.
  • Anchors go in solid, cured concrete. BendPak keeps anchors at least 6 in from any seam, control joint or crack. Never on hand-mixed concrete.
  • A post-tension slab or in-floor heat means scanning before anyone drills.
  • Most commercial two-posts run on 220 V single phase. Amps and breaker size come from the lift's manual. Wiring is a job for a licensed electrician.
  • Building permits and electrical work are separate from our install.
  • If you lease and cannot drill the slab, a two-post is out. Look at a freestanding four-post or mobile columns.

Installed price quoted as one number

The lift and our installation with anchors. Building permits and electrical work are arranged separately.. Call or send your bay details for a firm figure.

Compared with the alternatives

Two-post lifts compared with Four-post lifts and Scissor lifts and Heavy-duty truck lifts
Two-post liftsFour-post liftsScissor liftsHeavy-duty truck lifts
Best forGeneral repair, cars and light trucksStorage and drive-on serviceBays that can't take columnsBox trucks, medium duty, fleets
Typical capacity7,000 to 12,000 lb7,000 to 18,000 lb7,000 to 9,000 lb15,000 to 30,000 lb
Ceiling neededAbout 12 to 13 ft clearfloorColumns plus the car on topTo confirm per modelAbout 14 to 16 ft two-post
Underbody accessFull, wheels hang freeWheels on runways; jacks free themGood; centre partly blockedFull on a two-post
Floor spaceAbout 11 to 12 ft wideLongest; count the rampsCompact; ramps or flushTo confirm per model
Anchoring and slabAnchored, 4-1/4 in at 10,000 lbSome freestanding; 4-1/4 in commonSurface, or flush in a pitAnchored, 8 in at 15,000 lb

Common questions

How high does my ceiling need to be for a two-post lift?

A clearfloor 10,000 lb two-post is roughly 12 to 13 ft tall on common models, so your ceiling has to clear that with some margin. Measure to the lowest thing over the lift, like lights, heaters, sprinkler heads or door tracks, not the roof deck. With less than about 12 ft clear, a floorplate or low-ceiling model is usually the answer.

How thick does my concrete need to be?

It depends on the lift. BendPak's spec calls for at least 4-1/4 in of 3,000 PSI concrete under its 7,000 to 10,000 lb two-posts, 6-1/2 in at 12,000 lb, and 8 in at 15,000 and 18,000 lb. We check the spec for the exact lift before anything is drilled.

Should I get a 10,000 or a 12,000 lb two-post?

Around 10,000 lb suits cars, SUVs and half-ton pickups. Shops taking three-quarter and one-ton pickups, heavier vans or a lot of EVs usually step up to 12,000 lb. Size it for your heaviest regular vehicle, and remember the bigger lift can need thicker concrete.

Will a dually or a wide van fit between the columns?

That depends on the drive-through clearance, the gap between the columns. On common 10,000 lb models it is roughly 7.5 to 9 ft. We check it against your widest vehicle before you order.

Is the lift ALI certified?

ALI certification is given model by model, not to a whole brand. Adding non-certified accessories voids it while they are on. You can check any model in ALI's public Directory of Certified Lifts, and we can look one up with you.

Pricing a new lift?

Send your ceiling height and what you work on. You get one price for the lift, delivery and install.