Skip to content
Safe LiftSYSTEMS

Scissor lifts with no columns and no beam

A scissor lift raises the vehicle on a platform or pads with no posts in the way. A full-rise model is the alternative to a two-post when your bay cannot take columns.

7,000–9,000lb

Get a quote

Who a scissor lift is for

Shops that want standing room underneath but cannot fit columns. Scissors come as low-rise, mid-rise, full-rise and alignment models.

This page covers full-rise. Low-rise and mid-rise have their own page, and so do alignment lifts.

How it works

A scissor mechanism lifts the vehicle. The BendPak SP-7XE picks the vehicle up by the frame and has an open centre for access underneath.

On many full-rise scissors the mechanism blocks some of the centre of the undercarriage. Exhaust, transmission and driveline work can be more awkward than on a two-post.

Surface mount or flush mount

A surface-mount scissor sits on the slab with drive-up ramps. It needs no concrete work, but the ramps are in the way when the lift is down.

A flush-mount scissor is recessed into a pit so the platform is level with the floor. The bay works like a normal bay when it is down, but the pit means saw-cutting, forming and drainage.

Choosing between options

If your slab cannot take a two-post, a scissor can be one of the answers. If you need open access under the middle of the car, compare it with a two-post first.

What your bay needs

Measure to the lowest thing overhead. Final numbers come from the spec sheet of the exact model.

Bay requirements
CeilingNot yet confirmed
Floor spaceNot yet confirmed
Slab, surface mountNot yet confirmed
Flush mountPit with drainage
PowerNot yet confirmed

Before install day

  • A surface-mount scissor needs no concrete work.
  • A flush-mount scissor needs a pit cut and formed in the floor, with drainage. That bay is committed to the lift.
  • A post-tension slab or in-floor heat means scanning before any cutting or drilling.
  • Building permits and electrical work are separate from our install.

Installed price quoted as one number

The lift and our installation. Pit work for flush mount, building permits and electrical work are quoted separately.. Call or send your bay details for a firm figure.

Compared with the alternatives

Scissor lifts compared with Two-post lifts and Low-rise and mid-rise lifts and In-ground lifts
Scissor liftsTwo-post liftsLow-rise and mid-rise liftsIn-ground lifts
Best forBays that can't take columnsGeneral repair, cars and light trucksTires, brakes, body and detailDealers and express service
Typical capacity7,000 to 9,000 lb7,000 to 12,000 lb6,000 to 7,000 lbTo confirm per model
Ceiling neededTo confirm per modelAbout 12 to 13 ft clearfloorLow; Versalift tops 39.4 inTo confirm per model
Underbody accessGood; centre partly blockedFull, wheels hang freeWorking height, not standing roomTo confirm per model
Floor spaceCompact; ramps or flushAbout 11 to 12 ft wideCompact; Versalift 102 x 45 inClear bay when down
Anchoring and slabSurface, or flush in a pitAnchored, 4-1/4 in at 10,000 lbPortable, surface or flushExcavation and concrete work

Models we work with

BendPak SP-7XE

We sell, install and service

A 7,000 lb full-rise scissor that lifts by the frame, with an open centre.

Specs
Capacity7,000lb
MountingSurface; SP-7XEF flush
Max riseNot yet confirmed

Atlas SLP9K

We sell, install and service

A 9,000 lb full-rise scissor lift.

Specs
Capacity9,000lb
Max riseNot yet confirmed

Atlas FM9SL

We sell, install and service

A 9,000 lb scissor lift that sets into the floor so the bay stays flat.

Specs
Capacity9,000lb
MountingFlush
Pit sizeNot yet confirmed

Common questions

Is a scissor lift as good as a two-post for undercar work?

Not always. On a full-rise scissor the mechanism can block part of the centre of the undercarriage, so exhaust, transmission and driveline work can be harder. For brakes, wheels and body work it does the job with no columns in the way.

What is the difference between surface mount and flush mount?

Surface mount sits on the slab with ramps and needs no concrete work. Flush mount is set into a pit so the platform is level with the floor when down, which means cutting and forming a pit, with drainage.

Can a scissor lift work on a slab that won't hold a two-post?

Sometimes. When a slab fails for a two-post, a scissor lift or a freestanding four-post are among the usual answers. We check your slab and the spec of the exact lift first.

Pricing a new lift?

Send your ceiling height and what you work on. You get one price for the lift, delivery and install.