Skip to content
Safe LiftSYSTEMS

Buying your first two-post lift

A two-post is the everyday repair lift, and the right one depends on your vehicles and your bay more than the brochure. Settle these choices before you compare quotes.

Buying a lift / Checked

Start with your heaviest regular vehicle

Around 10,000 lb is the common class for cars, SUVs and half-ton pickups. Shops taking three-quarter and one-ton pickups, heavier vans or a lot of EVs usually step up to 12,000 lb. Fleets with box trucks look at 15,000 or 18,000 lb.

Size the lift for your heaviest regular vehicle, not your average one.

Total capacity is not the only limit. BendPak rates its 10APX at 10,000 lb total, but 5,000 lb per axle and 2,500 lb per arm. A vehicle under the total can still be over the limit on one axle.

Clearfloor or floorplate

This choice is about where the equalizing cables and hoses run. A clearfloor lift runs them through a crossbeam over the top. The floor stays clear, and there is usually a shutoff bar that stops the lift if a tall vehicle touches it.

A floorplate lift runs them through a plate on the floor that you drive over. Nothing sits above the columns, so it needs much less ceiling. For a low ceiling or tall vans, it is the right machine, not a downgrade.

Symmetric, asymmetric or both

On a symmetric lift the columns face each other squarely and the arms are the same length. The vehicle sits centred between the posts. That balances the load and suits long, heavy trucks and vans, but the doors open into the columns.

An asymmetric lift turns the columns and uses shorter front arms, so the car sits further back and the doors clear the posts. Rotary rotates the columns 30 degrees on its SPOA10-AV. Many lifts now have adaptable arms that do both, which suits a shop that works on cars and trucks.

Arm reach and adapters

Arm reach decides whether the lift can pick up a short-nose car and a long pickup in the same bay. Compare the published reach with the vehicles you actually see.

Ask what adapters come with the lift. Truck adapters and tall pads are what let the arms reach the right lift points on higher vehicles.

  • BendPak 10APX, published: front arms 24.5 to 50 inches, rear arms 32 to 59.25 inches
  • Rotary SPOA10-AV, published: front arms 18.5 to 41 inches, rear arms 28.5 to 58.25 inches

Check the bay before you pick a model

Ceiling: BendPak publishes an overall height of 145 inches for its 10AP and 157 inches for its 10APX. With less than about 12 feet clear, a floorplate or low-ceiling model is usually the answer.

Slab: BendPak's published minimum is 4-1/4 inches of concrete for its 7,000 to 10,000 lb two-posts and 6-1/2 inches at 12,000 lb. A capacity step can be a slab step.

Width and power: BendPak lists 135 or 145 inches overall width and 92 or 102 inches between the columns on its 10,000 lb models, and 220 volt single-phase power on the 10APX.

Look up the model's ALI certification

ALI certification applies to a lift model, not to a brand. The check is ALI's public Directory of Certified Lifts. If the model is listed, it is certified. ALI also says there is no such thing as pending or partial certification.

Installation and first use

We install two-posts from pretty much any brand, including lifts bought somewhere else. Building permits and electrical work are arranged separately. Before its first use, Ontario Regulation 851 section 51(1)(b) says a lifting device shall "be thoroughly examined by a competent person to determine its capability of handling the maximum load as rated, (i) prior to being used for the first time".

Common questions

What capacity two-post lift do most shops buy?

Around 10,000 lb is the common class for cars, SUVs and half-ton pickups. Shops that see three-quarter and one-ton pickups, heavier vans or many EVs usually step up to 12,000 lb. Size it for your heaviest regular vehicle, and check the per-axle and per-arm ratings as well as the total.

Is a floorplate two-post worse than a clearfloor?

No. A floorplate lift runs its cables and hoses through a plate on the floor instead of an overhead beam, so it needs much less ceiling. You give up the clear floor and the overhead shutoff bar. For a low ceiling or tall vans, it is the right choice.

How do I know if a two-post model is ALI certified?

Look the exact model up in ALI's public Directory of Certified Lifts. Certification is per model, so one certified model does not make every lift from that maker certified. If the model is not listed, it is not certified.

Will you install a two-post I bought somewhere else?

Yes. We install lifts from pretty much any brand, including lifts bought elsewhere. Tell us the make and model, and one of our people will confirm the install with you.

Pricing a new lift?

Send your ceiling height and what you work on. You get one price for the lift, delivery and install.