Skip to content
Safe LiftSYSTEMS

Installing lifts in Etobicoke industrial units

Before we quote an install in Etobicoke, we measure the clear height, check the slab and look at your power. Bought the lift somewhere else? We install those too.

What the buildings give you

A City report says Rexdale-Airport was largely built through the 1960s and 1970s, and its more recent buildings generally have clear heights between 16 and 20 feet.

Clear height on a listing isn't the same as usable height over a bay. Heaters, lights, sprinkler pipes and door tracks all hang down from the roof. We measure to the lowest one.

Newer units with 16 to 20 feet can suit taller lifts and higher vehicles. An older unit on the same street may not match that, so don't assume one building's number holds next door.

Whether a lift fits depends on the lift, the vehicle and how high you need to raise it. We check all three together.

Older slabs, new anchors

Floors poured decades ago have seen racking, forklifts, trenches and patches. The surface can look fine and still hide a thin or cut section.

Every lift maker publishes a minimum slab thickness for its lift. We check that number against your floor before anyone drills.

Tell us if the floor has ever been cut for drains, pits or trenches, and when it was poured if you know.

If the slab can't take anchors, look at a freestanding four-post, mobile columns or a new engineered pad.

A tight market and leased units

Rexdale-Airport had nearly 27 million square feet of rentable industrial space in 2021, with an average vacancy rate of 4%. With so little space free, a shop may have to lease the unit that comes up, not the one it would design.

If you're choosing between two units, send us the details of both. We can tell you which one suits the lift you need before you sign.

In a lease, get your landlord's written OK to anchor the lift and run any new wiring. We give you the lift's slab, height and power needs to take to them.

Building permits and electrical work sit outside our install scope. Your electrician gets the lift's power requirements from us in writing.

New builds and dealer shops

Some installs start with a new floor. In 2019, City planners recommended approving a two-storey auto dealership and service facility on The Queensway, on land designated General Employment Areas.

New construction is the best time to plan lifts, because slab, height and power can be designed in. Bring us in before the floor is poured.

In the Sherway area, the City notes industrial uses south of the CP rail corridor, with offices, shops and a hospital close by. In mixed areas like that, check zoning for your use before you sign.

Lifts bought somewhere else

We install lifts bought from someone else, new or used. Send the make, the model and the install manual. If you haven't bought yet, send the spec sheet and your measured height, and we tell you if it suits the bay.

A used lift should come with all its parts, including arms, adapters, locks and the power unit. Missing pieces can hold up the install.

Section 51(1)(b) of Ontario Regulation 851 calls for a lift to be thoroughly examined by a competent person "prior to being used for the first time". We can book that exam alongside the install.

Common questions

What clear height do Etobicoke industrial units have?

It varies by building. A City report says the more recent buildings in Rexdale-Airport generally have 16 to 20 feet. Older units can differ, so we measure yours.

Can you install in a leased unit near the airport?

Yes, once the landlord approves anchoring and any wiring. We give you the lift's needs in writing for that request.

Do you install lifts we bought from another seller?

Yes. Send the make, the model and the manual, and we check it against your bay before booking the install.

Is the building permit part of your install?

No. Building permits and electrical work are separate. We tell you and your electrician what the lift needs.

We're building a new service shop. When should we call?

Before the slab is poured, if you can. Lift choice affects slab thickness, bay layout and power, and those are easier to plan than to fix later.

Pricing a new lift?

Send your ceiling height and what you work on. You get one price for the lift, delivery and install.