Skip to content
Safe LiftSYSTEMS

Mohawk lift not lowering, drifting down or raising uneven

We repair and inspect Mohawk lifts in Toronto and the GTA, working from Mohawk's own manuals.

Independent service. We are not affiliated with Mohawk.

Lift stuck up, or dropping?

Keep everyone clear and don’t go under it. Call 416-771-0499.

Common Mohawk lift problems

Mohawk lift will not lower

What usually causes it

  • Mechanical locks still engaged
  • Lift uneven from side to side
  • Posts out of square
  • Debris in the posts, such as tools
  • Something under the vehicle or the lift

What we do

Keep everyone clear and do not go under the lift or the vehicle. Call us. Our technician checks for obstructions, lock engagement and post alignment, brings the lift down safely and fixes the cause.

Mohawk lift drifts down slowly

What usually causes it

  • Safeties not engaged
  • Contamination in the power unit lowering valve
  • A diverter valve or bleeder valve that needs service
  • Internal hydraulic leaks

What we do

Keep everyone clear and do not go under the lift or the vehicle. Call us. Our technician runs Mohawk's hydraulic safety checks with no vehicle on the lift to find the leaking valve or cylinder, then services or replaces it.

Mohawk lift raises uneven

What usually causes it

  • Air in the hydraulic system
  • Incorrect cylinder shims, so the carriage bearings touch the carriage stops
  • Posts out of square
  • Uneven shop floor

What we do

Our technician checks the hydraulics, cylinder shims, post alignment and floor, and sets the lift to Mohawk's specs.

Mohawk lift will not raise a load

What usually causes it

  • Low hydraulic fluid
  • Pressure relief valve out of adjustment or contaminated
  • Wrong voltage at the power unit
  • Vehicle too heavy for the lift

What we do

Our technician checks the power unit, relief valve, fluid and supply voltage. Any change to the building wiring is done by or under a licensed electrician.

Mohawk mechanical lock re-engages or is hard to pull

What usually causes it

  • J-bar out of adjustment
  • Spring plunger out of adjustment
  • Lock flipper sticking on the lock bar

What we do

Our technician checks the lock parts on both posts, sets them to Mohawk's specs and tests the locks under a vehicle.

Worn, damaged or broken parts are replaced with parts approved by Mohawk, or parts that meet Mohawk's original specs, as ANSI/ALI ALIS calls for.

Mohawk lifts we see

Independent service. We are not affiliated with Mohawk.

Mohawk is a US maker of heavy-duty lifts. Its range includes two-post lifts from 7,000 to 30,000 lb, mobile columns from 18,000 to 30,000 lb per column, and heavy four-post lifts.

If your Mohawk is under warranty

Mohawk's warranty says Mohawk may decline responsibility when repairs have been made or attempted by others. If your lift is still under warranty, check with Mohawk before you book a repair.

What to tell us when you call

A few details let the right person call you back ready.

  • Your shop address
  • The make and model of the lift, and the serial number if you can read it
  • What the lift is doing, or not doing
  • Whether a vehicle is on the lift, and whether it is up or down
  • Your last inspection or service record, if you have it

Inspecting Mohawk lifts

Ontario requires every lift in your shop to be examined at least once a year, with a signed record.

We inspect Mohawk lifts along with every other lift in the shop, in one visit. Anything that needs repair goes on the record in plain words.

Common questions

Are you a Mohawk dealer?

No. This is independent service. We are not affiliated with Mohawk. We repair and inspect Mohawk lifts, and Mohawk's own manuals set the checks and specs.

Will an independent repair affect my Mohawk warranty?

It can. Mohawk's warranty says Mohawk may decline responsibility when repairs have been made or attempted by others. The warranty is for the original buyer only. If your lift is under warranty, check with Mohawk first.

Why doesn't my Mohawk lock reset after it has been released?

Mohawk's manual says its latches do not reset on their own after they are released. The lift has to be raised about 2 inches to reactivate them. If the locks still do not catch, keep people clear and call us.

What parts do you use on a Mohawk repair?

ANSI/ALI ALIS, the North American standard for lift installation and service, says worn, damaged or broken parts are replaced with parts approved by the original manufacturer, or parts that meet the original manufacturer's specs. That is the rule we follow on Mohawk lifts.

Lift down?

Call now. Tell us the make, the model and what it's doing, so the technician comes ready for that lift.