Lift cables and chains: when they get replaced
Cables and chains carry or level the load on many lifts. The manufacturer's manual sets how often they are checked and when they come out.
Running and maintaining lifts / Checked
What cables and chains do
On many two-posts, equalizing cables keep the two carriages level as the lift rises. Four-posts such as BendPak's HD-9 hang the runways on wire rope cables. Some two-posts use a chain driven by the cylinder. BendPak's XPR-9 manual describes a chain between the base plate and the lift head.
The ANSI/ALI ALIS standard groups them together as wire rope and roller or leaf chain used to suspend or synchronize the load.
The first rule in the manuals
BendPak's 10AP, XPR-9 and HD-9 manuals all carry the same danger notice: do not use the lift if the cables are damaged or extremely worn.
The manuals say that if a vehicle is raised when the damage is noticed, it is lowered very carefully, then the lift is taken out of service, disconnected from power, and repair is arranged. Call us before anyone works under it.
How often the manuals call for checks
The 10AP, XPR-9, XPR-12CL and HD-9 manuals call for lifting cables to be visually inspected at least once each day when the lift is in use. They cite the American Petroleum Institute's Recommended Practice 54.
On longer intervals, manuals differ. The 10AP and XPR-9 manuals call for a careful check of the equalizing cables every three to five years, or right away at signs of damage. The XPR-12CL manual calls for lifting cables to be replaced every three to five years, or when visible damage appears. Read the manual for your model.
The manuals also call for wire rope to be kept well lubricated, at intervals no longer than three months. The HD-9 schedule lists it monthly.
When the manuals say a cable comes out
The manuals say any lifting cable that meets the removal criteria must be replaced immediately. The criteria they list are below. Judging them properly takes a trained lift technician and the right conditions, so treat this as what to expect from a service visit, not a shop checklist.
- Six randomly distributed broken wires in any one lay length, or three broken wires in one strand in one lay length
- Corrosion that pits the wires or connectors
- Kinking, crushing, cutting, bird-caging or a popped core
- Wear of more than 10% of a wire's original diameter
- Heat damage
Chains
ALIS says every planned service procedure includes periodic examination of wire rope and chain used for load suspension or synchronization. The maker's instructions come first.
Where the maker gives no criteria, ALIS gives guidance based on ASME B29.24. It retires a chain for problems such as stretch past a set limit, twist, side bow, cracked link plates, turned or loose pins, broken rollers, tight joints and severe corrosion.
Parts and records
ALIS says replacement parts must be approved by the original manufacturer or meet its original specifications. It also bars any modification to a lift without the maker's written permission.
ALIS has the service technician keep a record of each service and repair, including parts replaced and measurements taken, with a copy to the owner. Keep those logs on or near the lift. The annual examination under Ontario Regulation 851 is a separate signed record.
Common questions
How often should lift cables be replaced?
It depends on the manual. BendPak's XPR-12CL manual calls for lifting cables to be replaced every three to five years or when visible damage appears. Its 10AP and XPR-9 manuals call for a careful check every three to five years and replacement when there are signs of damage or extreme wear. Follow the manual for your model.
Can I keep using a lift with a frayed or kinked cable?
No. BendPak's manuals say not to use the lift if the cables are damaged or extremely worn. If a vehicle is up, it is lowered very carefully, and the lift is taken out of service and disconnected from power until it is repaired.
Do replacement cables have to come from the lift maker?
The ANSI/ALI ALIS standard says replacement parts must be approved by the original equipment manufacturer or meet the original manufacturer's specifications. It also bars modifying a lift without the maker's written permission.
Do you replace lift cables and chains?
Yes. Cable and chain work is part of the lift repair and service we do on pretty much any brand. Call 416-771-0499 with the make and model and what you are seeing, and tell us if a vehicle is on the lift.
Where this comes in
Lift down?
Call now. Tell us the make, the model and what it's doing, so the technician comes ready for that lift.