Skip to content
Safe LiftSYSTEMS

Ceiling height by lift type

Ceiling height decides which lift can go in a bay. The number that matters is clear height to the lowest thing over the lift, not the roof deck.

Planning the bay / Checked

Measure clear height, not roof height

Measure from the floor to the lowest thing hanging over where the lift will stand. That is often not the roof. Take the measurement at each planned lift position, because height changes across a building.

The ANSI/ALI ALIS standard says to check for overhead doors in the raised position, and to make sure the ceiling clears lifts with overhead structures, tall vans and trucks, and raised hoods when the vehicle is fully lifted.

  • Unit heaters and light fixtures
  • Sprinkler heads
  • Overhead door tracks and openers, with the door open
  • Hose reels and ductwork
  • Roof joists that drop below the deck

Clearfloor two-post lifts

A clearfloor two-post has a crossbeam across the top, so the lift itself is the tallest thing in the bay. Your clear height has to be above the lift's overall height, with some margin.

The overhead shutoff bar also limits how high a tall vehicle can go. BendPak publishes a floor-to-overhead-switch height of 139.5 inches on its 10AP.

  • BendPak 10AP: 145 inches (12 ft 1 in) overall, published
  • BendPak 10APX: 157 inches (13 ft 1 in) overall, published
  • BendPak 10AP-168: marketed as 168 inches extended height
  • Rotary SPOA10-AV: 11 ft 11-1/2 in overall, or 12 ft 5-1/2 in with Shockwave, published

Floorplate two-post lifts

A floorplate two-post has nothing above the columns, so it needs much less ceiling. With less than about 12 feet clear, a floorplate or low-ceiling model is usually the answer.

The raised vehicle still needs room. Check the column height on the model's spec sheet, then add the height of your tallest vehicle at full rise.

Four-post, scissor and in-ground lifts

These lifts have no overhead beam. The limit is the vehicle itself: its height, plus how high the lift raises it, plus a raised hood if you open one.

Rise differs a lot between models, so take it from the spec sheet. Low-rise and mid-rise scissors lift less than full-rise lifts, which is one reason they suit tight buildings. For comparison, BendPak publishes a maximum rise of 79.5 inches on its 10APX two-post.

Mobile column lifts

Mobile columns have no crossbeam, so the lift sets no fixed ceiling line. The raised vehicle still does. On buses and trucks, check the roof height of your tallest vehicle at the rise you need, and any door tracks along the path between bays.

Parking lifts and car stackers

Stackers work differently. At the moment the lower car comes out, both cars are inside the clear height. So the upper car plus the lower car must fit within the clear height minus a fixed allowance for the platform.

A pit buys independent access and a clear floor. It does not buy room for taller cars. Parking lifts in Ontario are also TSSA-regulated elevating devices, unlike shop hoists.

The door counts too

A lift is no use if the vehicle can't get into the bay. Measure the door opening height and width, and where the door track lands. The lift has to come in through a door as well.

Common questions

What ceiling height do I need for a two-post lift?

It depends on the model. BendPak publishes 145 inches overall for its 10AP and 157 inches for its 10APX, and Rotary publishes 11 ft 11-1/2 in for its SPOA10-AV. Your clear height to the lowest obstruction must be above that with margin. With less than about 12 feet clear, a floorplate or low-ceiling model is usually the answer.

Where do I measure ceiling height from?

From the floor to the lowest thing over the lift's footprint, such as a heater, light, sprinkler head or open door track. Do it at each planned lift position with the overhead door fully open. The roof deck height does not matter if something hangs below it.

Does a pit give a car stacker more height?

No. When the lower car comes out, both cars are inside the clear height, pit or no pit. A pit gives independent access and a clear floor. It does not give room for taller cars.

Can a shop with a low ceiling still have a lift?

Often, yes. A floorplate two-post has nothing above the columns, and scissor lifts have no overhead structure at all. The raised vehicle still needs room, so we check your clear height against the exact model and your tallest vehicle.

Pricing a new lift?

Send your ceiling height and what you work on. You get one price for the lift, delivery and install.