Skip to content
Safe LiftSYSTEMS

Rotary lift won't lower, drifts or lifts uneven

We sell, install and service Rotary lifts across Toronto and the GTA. Here is what usually causes the common Rotary problems, and what our technician does about them.

Lift stuck up, or dropping?

Keep everyone clear and don’t go under it. Call 416-771-0499.

Common Rotary lift problems

Rotary two-post won't come down off its locks

What usually causes it

  • Broken latch cable, so one side stays locked
  • Latch cable off its sheaves or upper guides
  • Latch cable loose
  • Motor, pump or cylinder failure, so the lift cannot raise off the latches

What we do

Keep everyone clear and do not go under the lift or the vehicle. Call us. Our technician checks the latch cable, its routing and the latch parts in both columns, and the power unit and cylinders. We bring the lift down safely, replace what is broken and test the locks through the full rise.

Rotary lift slowly settles down

What usually causes it

  • Debris in the check valve seat
  • Debris in the lowering valve seat
  • External oil leaks

What we do

Keep everyone clear and do not go under the lift or the vehicle. Call us. Our technician finds where the lift is losing pressure, from the power unit valves to the hoses, fittings and cylinders, and repairs the valve or the leak.

Rotary lift goes up out of level

What usually causes it

  • Equalizer cables out of adjustment
  • Lift installed on an out-of-level floor

What we do

Our technician checks the equalizer cables for wear and tension and checks the columns for level, then sets the lift to Rotary's specs. If the floor is the problem, we tell you what it will take.

Rotary locks don't engage as the lift goes up

What usually causes it

  • Rusted latch shafts, most often in wash bays, damp areas or outdoor installs
  • Broken latch spring
  • Latch cable out of adjustment

What we do

Do not work under a lift that is not sitting on its locks. Our technician checks every latch, spring and cable, and repairs or replaces parts so both sides lock as designed.

Rotary anchors won't stay tight, or the concrete is cracking

What usually causes it

  • Anchor holes drilled oversize
  • Concrete too thin or not strong enough to hold the lift
  • Cracks or loose concrete around the floor anchors

What we do

Take the lift out of use and call us. Our technician checks the anchors and the concrete around each column, and tells you what the floor needs before the lift goes back in service.

Worn, damaged or broken parts are replaced with parts approved by Rotary, or parts that meet Rotary's original specs, as ANSI/ALI ALIS calls for.

Rotary lifts we see

Rotary makes two-post lifts like the SPOA7 and SPOA10, four-post lifts, in-ground lifts like the MOD35, and mobile column sets for buses and trucks.

We supply, install and service the Rotary range.

Rotary's five signs a lift needs repair

Rotary lists five signs that a lift needs repair. Rotary says fixing them promptly cuts downtime and the risk of injury. If you see one, call us.

  • Hydraulic fluid leaks
  • Locks or restraints not working correctly
  • Bent parts or heavy wear on any lift component
  • Damaged or badly worn contact points, including adapters
  • Cracks or loose concrete around the floor anchors

What to tell us when you call

A few details let the right person call you back ready.

  • Your shop address
  • The make and model of the lift, and the serial number if you can read it
  • What the lift is doing, or not doing
  • Whether a vehicle is on the lift, and whether it is up or down
  • Your last inspection or service record, if you have it

Inspecting Rotary lifts

Ontario requires every lift in your shop to be examined at least once a year, with a signed record.

We inspect Rotary lifts along with every other lift in the shop, in one visit. Anything that needs repair goes on the record in plain words.

Common questions

Do you work on Rotary lifts someone else installed?

Yes. We install, inspect and service lifts from pretty much any brand, including Rotary. Tell us the model and what the lift is doing.

Can you supply a new Rotary lift?

Yes. We supply, install and service Rotary lifts, including two-post, four-post, in-ground and mobile column models.

What are the signs my Rotary lift needs repair?

Rotary lists five: hydraulic fluid leaks, locks or restraints not working correctly, bent or badly worn lift parts, damaged or worn contact points and adapters, and cracks or loose concrete around the floor anchors.

What parts do you use on a Rotary repair?

ANSI/ALI ALIS, the North American standard for lift installation and service, says worn, damaged or broken parts are replaced with parts approved by the original manufacturer, or parts that meet the original manufacturer's specs. That is the rule we follow on Rotary lifts.

Lift down?

Call now. Tell us the make, the model and what it's doing, so the technician comes ready for that lift.