Skip to content
Safe LiftSYSTEMS

Hunter alignment lift rack locks, cables and leaks

We repair and inspect Hunter four-post and scissor alignment lift racks in Toronto and the GTA.

Independent service. We are not affiliated with Hunter.

Lift stuck up, or dropping?

Keep everyone clear and don’t go under it. Call 416-771-0499.

Common Hunter lift problems

Hunter RX lift will not lower and shows MISMATCHED LOCKS

What usually causes it

  • The locks caught at different heights, so the lift turns off the lower button until it is levelled again

What we do

Keep everyone clear. If the message keeps coming back, our technician checks the locks and the levelling system on the rack and repairs the cause of the mismatch.

Hunter lift stops responding and warning lights flash

What usually causes it

  • The lift detected repeated short presses of the raise button and went into a time-out
  • Jogging the raise button like this can wear out the motor early

What we do

If the lift still will not run after the time-out, our technician checks the motor, power unit and controls.

Hunter four-post locks not engaging or releasing properly

What usually causes it

  • Damaged lock pins that no longer lock and unlock freely
  • Rusty lock parts or a broken lock spring

What we do

Keep everyone clear and do not go under the lift or the vehicle. Call us. Our technician checks every lock and pivot lock pin on the rack, and repairs or replaces the parts so the locks engage and release as designed.

Rust, broken strands or kinks in Hunter lift wire ropes

What usually causes it

  • Road salt and moisture getting into the core of the rope
  • Ropes not kept lubricated
  • Solvents or corrosive agents splashed on the ropes

What we do

Stop using the lift. Hunter's manual says to replace wire ropes right away at any sign of damage. Our technician inspects the ropes and sheaves and replaces damaged ropes.

Hunter power unit oil level keeps dropping

What usually causes it

  • An oil leak somewhere in the hydraulic system

What we do

Hunter's manual says to find the source of any oil loss and repair it right away. Our technician traces the leak and repairs it.

Worn, damaged or broken parts are replaced with parts approved by Hunter, or parts that meet Hunter's original specs, as ANSI/ALI ALIS calls for.

Hunter lift racks we see

Independent service. We are not affiliated with Hunter.

Hunter makes alignment lift racks: four-post racks like the L451 and L454, RX scissor lift racks, and heavy-duty four-post and pit racks.

Hunter equipment we do not supply

Hunter sells its aligners, balancers and other equipment through its own representatives, so we do not supply it. We still install, inspect and service the lifts in a shop that runs Hunter.

What to tell us when you call

A few details let the right person call you back ready.

  • Your shop address
  • The make and model of the lift, and the serial number if you can read it
  • What the lift is doing, or not doing
  • Whether a vehicle is on the lift, and whether it is up or down
  • Any message or warning light showing on the lift's controls
  • Your last inspection or service record, if you have it

Inspecting Hunter lifts

Ontario requires every lift in your shop to be examined at least once a year, with a signed record.

We inspect Hunter lifts along with every other lift in the shop, in one visit. Anything that needs repair goes on the record in plain words.

Common questions

Are you a Hunter dealer?

No. This is independent service. We are not affiliated with Hunter. We repair and inspect Hunter lift racks, working from Hunter's own manuals.

Can you sell me a Hunter aligner or balancer?

No. Hunter sells its aligners, road force balancers and other equipment through its own representatives. We supply other alignment and wheel service brands, and we service the lifts in a Hunter shop.

Why does my Hunter lift say MISMATCHED LOCKS?

Hunter's RX manual says the message means the locks are not matched, and the lower button is disabled until the lift is levelled again. If it keeps happening, call us.

What parts do you use on a Hunter repair?

ANSI/ALI ALIS, the North American standard for lift installation and service, says worn, damaged or broken parts are replaced with parts approved by the original manufacturer, or parts that meet the original manufacturer's specs. That is the rule we follow on Hunter lifts.

Lift down?

Call now. Tell us the make, the model and what it's doing, so the technician comes ready for that lift.