Skip to content
Safe LiftSYSTEMS

BendPak lift won't lower, won't stay up or runs rough

We sell, install and service BendPak two-post, four-post, scissor and mobile column lifts across the GTA. These are the problems BendPak's own manuals list, and what we do about them.

Lift stuck up, or dropping?

Keep everyone clear and don’t go under it. Call 416-771-0499.

Common BendPak lift problems

BendPak two-post won't lower once raised

What usually causes it

  • Low hydraulic fluid
  • Air in the hydraulic system
  • A pinched or leaking hydraulic hose
  • No power reaching the power unit
  • Lift overloaded, or the load off balance

What we do

Keep everyone clear and do not go under the lift or the vehicle. Call us. Our technician checks the power supply, power unit, fluid and hoses, finds why the lift will not come down, and brings it down safely before repairing the fault.

One side of a BendPak two-post will not lower

What usually causes it

  • A broken safety cable, so the lock on the offside post stays engaged

What we do

Keep everyone clear and do not go under the lift or the vehicle. Call us. Our technician releases the stuck side safely, brings the lift down and replaces the safety cable before the lift goes back in use.

BendPak four-post runways stop at the nearest lock and won't go lower

What usually causes it

  • Air lines disconnected or leaking, so the locks do not release

What we do

Keep everyone clear and do not go under the lift or the vehicle. Call us. Our technician checks the air supply and every section of air line to the locks, repairs the leak or connection, and tests all four locks.

BendPak lift drifts down or will not stay up

What usually causes it

  • Hydraulic fluid leaks
  • Lift left off its safety locks
  • On PCL mobile columns: a leaking check valve, lowering valve, cylinder or fitting

What we do

Keep everyone clear and do not go under the lift or the vehicle. Call us. Our technician traces the leak or the valve that is letting the lift down, and repairs or replaces it.

Vehicle not level on a BendPak lift, or arms squeak and move jerkily

What usually causes it

  • Safety locks engaged at different heights
  • Air left in the hydraulic system

What we do

Our technician checks lock engagement in both posts and the hydraulic system, and corrects the cause before the lift goes back in use.

BendPak's manuals call for original BendPak or BendPak-approved parts, or parts that meet or exceed the original specs. ANSI/ALI ALIS says the same.

BendPak lifts we see

BendPak two-post lifts like the XPR-9 and 10AP series, HD-9 and HD-7 four-post lifts, the MDS-6 mid-rise scissor lift and PCL mobile column lifts.

We supply, install and service the BendPak range.

BendPak says take it out of service

BendPak's manuals say a lift that is not working correctly must be taken out of service until it is fixed. Keep people clear and call us.

What to tell us when you call

A few details let the right person call you back ready.

  • Your shop address
  • The make and model of the lift, and the serial number if you can read it
  • What the lift is doing, or not doing
  • Whether a vehicle is on the lift, and whether it is up or down
  • Your last inspection or service record, if you have it

Inspecting BendPak lifts

Ontario requires every lift in your shop to be examined at least once a year, with a signed record.

We inspect BendPak lifts along with every other lift in the shop, in one visit. Anything that needs repair goes on the record in plain words.

Common questions

Can you service a BendPak lift I bought somewhere else?

Yes. We install, inspect and service lifts from pretty much any brand, including BendPak. Tell us the model and what the lift is doing.

Why does one side of my BendPak two-post stay up?

BendPak's 10AP manual says that when a safety cable breaks, the offside lift head will not lower. The cable has to be replaced. Keep people clear and call us.

Should I keep using a BendPak lift that is acting up?

No. BendPak's manuals say a lift that is not working correctly must be taken out of service until it is fixed.

What parts do you use on a BendPak repair?

BendPak's manuals call for original BendPak or BendPak-approved parts, or parts that meet or exceed the original manufacturer's specs. That is the rule we follow on BendPak lifts.

Lift down?

Call now. Tell us the make, the model and what it's doing, so the technician comes ready for that lift.