Skip to content
Safe LiftSYSTEMS

Atlas lift locks, cables and power unit problems

We sell, install and service Atlas two-post and four-post lifts across Toronto and the GTA. Here is what usually causes the common Atlas problems, and what our technician does.

Lift stuck up, or dropping?

Keep everyone clear and don’t go under it. Call 416-771-0499.

Common Atlas lift problems

Atlas two-post will not lower

What usually causes it

  • Locking latch still engaged on the latch rack
  • Latch release cable broken or out of adjustment

What we do

Keep everyone clear and do not go under the lift or the vehicle. Call us. Our technician checks the latches and release cable in both columns, brings the lift down safely and repairs or replaces the release parts.

Atlas 412 four-post will not come down off its locks

What usually causes it

  • Shop air below the lift's rated pressure
  • An air leak, or a fault at the air control valve or filter regulator

What we do

Keep everyone clear and do not go under the lift or the vehicle. Call us. Our technician checks the air supply, air lines, air control valves and filter regulator, repairs the fault and tests every lock.

Atlas lift motor will not run

What usually causes it

  • Failed AC contactor, so power does not reach the motor
  • Tripped breaker or blown fuse
  • Incorrect voltage or a poor wiring connection
  • A limit switch open

What we do

Our technician checks the supply, contactor, switches and motor, and repairs the fault. Any change to the building wiring is done by or under a licensed electrician.

Atlas lift raises unevenly

What usually causes it

  • Equalization cables too tight or too loose
  • Lift installed on an out-of-level floor

What we do

Our technician checks the equalization cables for wear and tension and the columns for level, and sets the lift to Atlas's specs.

Atlas four-post stopped with one corner caught on its safety

What usually causes it

  • A lifting cable has slackened or failed, and the slack cable safety has caught the runway

What we do

Keep everyone clear and do not go under the lift or the vehicle. Call us. Our technician inspects every lifting cable and sheave, replaces the damaged cable and checks the safety devices before the lift goes back in use.

Worn, damaged or broken parts are replaced with parts approved by Atlas, or parts that meet Atlas's original specs, as ANSI/ALI ALIS calls for.

Atlas lifts we see

Atlas baseplate two-posts like the PVL9BP, BP10000X and BP12000X, overhead two-posts like the 9KOH, and four-post lifts from the Garage PRO8000 and 408SL to the commercial 412 and 414.

We supply, install and service the Atlas range.

How Atlas locks work

On the Atlas 9KOH two-post, the locking latches drop into the latch rack as the lift rises, and a release cable lifts them off before the lift can lower.

The Atlas 412 four-post has a pneumatic system with a rated pressure of 6 to 8 bar, so it needs shop air to work as designed.

What to tell us when you call

A few details let the right person call you back ready.

  • Your shop address
  • The make and model of the lift, and the serial number if you can read it
  • What the lift is doing, or not doing
  • Whether a vehicle is on the lift, and whether it is up or down
  • Your last inspection or service record, if you have it

Inspecting Atlas lifts

Ontario requires every lift in your shop to be examined at least once a year, with a signed record.

We inspect Atlas lifts along with every other lift in the shop, in one visit. Anything that needs repair goes on the record in plain words.

Common questions

Do you sell Atlas lifts?

Yes. We supply, install and service Atlas two-post and four-post lifts, from home garage models to the commercial 412 and 414.

Do Atlas lifts need shop air?

Some do. The Atlas 412 four-post manual lists a rated pneumatic pressure of 6 to 8 bar, with a filter regulator on the air supply. Tell us your model and we will tell you what it needs.

Can you install an Atlas lift I bought online?

Yes. We install, inspect and service lifts from pretty much any brand. Tell us the model, and one of our people will confirm the work with you.

What parts do you use on a Atlas repair?

ANSI/ALI ALIS, the North American standard for lift installation and service, says worn, damaged or broken parts are replaced with parts approved by the original manufacturer, or parts that meet the original manufacturer's specs. That is the rule we follow on Atlas lifts.

Lift down?

Call now. Tell us the make, the model and what it's doing, so the technician comes ready for that lift.